Plastic Injection Moulding Machines due to production closure
Starts: 11 November 2025 at 05:00 GMT
Ends: 16 December 2025 at 14:00 GMT
Due to closure, sale of 2017 Haitian and 2012 Welltec Injection Moulding machines and moulds ready for production. Please see the sale information section for any additional fees that may be applicable upon purchasing an item. For Lots 3,4 and 5 seller will provide loading onto the buyer’s vehicle free of charge however, the buyer is responsible for properly securing the item. NOTE: Vendor to approve all closing bids prior to Apex final invoicing.
Share:
Showing 5 of 5 lots
- LOT 1
![site]()
A complete, ready-to-use mushroom crate production line with 2017 HAITIAN MARS II 3200/1700 ECO.
Injection moulding machine: 65 mm screw, approximately 929 cm3 injection. Gauge between tie bars 680 x 680 mm. Equipped with a servomotor controlled by a KEB inverter. 14,000 operating hours. Equipped with a dryer and a plastic conveyor. S/No 201707032030878 (2017). 2019 Automatic mold with heated channels, box weight 210 g. 2011 SHINI SIC-10 A industrial refrigerator. S/No 2CA11100013 (2011). Plastic mill, 5.5 kW motor, 8 knives (5 fixed + 3 movable). - LOT 2
![site]()
2012 WELLTEC TTI-380 SE Injection Moulding Machine
Screw 70 mm. Tie bar clearance 740 x 740 mm. Shot weight approximately 1100 g. Injection pressure 180 bar. Injection speed 163 cm3/s. Screw r.p.m 175 r.p.m. Number of ejectors 13 pcs. Minimum form height 250 mm. Maximum form height 740 mm. The machine is in very good condition, functional, with approximately 32,900 hours of operation. Includes a winch, dryer, and dye feeder. Machine weight 14400 kg. S/No DH-22700684/70 (2012) - LOT 3
![site]()
Set of moulds for a 100 CM MULTIFUNCTIONAL CHILDREN'S TOY KITCHEN
The set includes: INJECTION MOULDING- KITCHEN FRONT injection mould, - COUNTERTOP injection mould, - HOOD injection mould, - FIREPLACE injection mould, - DOOR injection mould, - DISHWASHER STRAINER + OVEN STRAINER injection mould, - KNOBS + TAP KNOB injection mould, - CUTLERY SET injection mould, - LIDS injection mould- POT + FRYING PAN injection mould, - CUPS injection mould, - SMALL PLATES injection mould, - LARGE PLATES injection mould, - GRAPE LEAVES injection mould. EXTRUSION MOULDING: - mould EGGS, - GRAPES form, - SAUSAGES form, - BUN + CROISEL form, - TAP form, - BANANA + PINEAPPLE form, - PINEAPPLE LEAVES form, - CANS form - LOT 4
![site]()
TOY INJECTION MOULD SET: TROLLEY WITH HANDLE + DAISY WHEELBAR WITH SHOVEL AND RAKE.
The set includes: - Injection mould for the trolley body, - Injection mould for the trolley handle, - Injection mould for the wheelbarrow body, - Injection mould for the wheels (for wheelbarrow and trolley), - Injection mould for the hubcaps (for wheelbarrow and trolley),- Injection mould for the shovel and rake - LOT 5
![site]()
Set of injection moulds for a CHILDREN'S TRICYCLE toy.
The set includes: - injection mould for INNER REAR WHEEL, - injection mould for INNER REAR WHEEL, - injection mould for INNER FRONT WHEEL, - injection mould for OUTER FRONT WHEEL, - injection mould for WHEEL CAP (front + rear), - injection mould for PEDAL, - injection mould for FOOTREST, - injection mould for FOOTREST SCREW, - injection mould for SEAT, - injection mould for BUCKET, - injection mould for BIKE BODY, - injection mould for HANDLEBAR, - injection mould for FORK, - injection mould for RIGHT + LEFT HANDLE, HANDLE FOR PUSH RINGINCREASING THE HEIGHT OF THE STEERING WHEEL. Tool kit for making the drive shaft: - Axle clamping tool, - Axle bending tool for the right side of the axle, - Axle bending tool for the left side of the axle. Including also approximately 1,000 pieces of ready-made push rods.
Essential Information
General Information
- Auction Dates
- Starts: 11 November 2025 at 05:00 GMTEnds: 16 December 2025 at 14:00 GMT
- Site Address
- CzestochowaPoland
- Viewing Days
- By Appointment OnlyBy Appointment Only. Please contact Apex to make an appointment.
Fees & Payment
- Currency
- EUR
- Buyers Premium
- 18% or as specified on individual items
- Payment
General payment information
- A link to the invoice will be emailed to successful bidders
- Payment is due immediately on receipt of invoice
- All payments must be made in the currency on the invoice issued.
- Accepted forms of payment are bank transfer ONLY. We do NOT accept payment by card, cash or cheque
- NB: Please reference invoice number on bank transfer.
Goods
- Clearance days
- 22 December 2025 at 07:00 GMT - 09 January 2026 at 15:00 GMTCollections strictly by appointment only. Dates excluding 24,25,26th.
- General Collection Information
Collection
For Lots 3,4 and 5 seller will provide loading onto the buyer’s vehicle free of charge however, the buyer is responsible for properly securing the item.
- Buyers are fully responsible for removal of items plus all transport and rigging charges.
- Items are only available for collection once the transfered funds have cleared, and a collection appointment has been booked.
- Buyers or third party movers must present an invoice to the on-site personnel when removing their items.
- Buyers must complete the removal of items within the clearance deadline. Normal removal hours are Monday to Friday, from 9am to 4pm (local time) unless otherwise stated.
- Contact and removal information will be emailed at the time invoices are issued.
- For a list of companies that can assist with removals and transportation please visit the Apex Auctions website's Service Providers section.
- Sales Contacts
- Auction informationZuzanna Bodziachowska-KluzaAlmax Spolka Cywilna
Częstochowa
42-200
Poland zkluza@apex-group.com+48 34 888 1030